After mitigation wraps up, the house usually looks worse than it did on the day the leak started. Rebuilding all of that is restoration, which is its own trade with its own crews.
Our referral line links Arlington homeowners with independent, licensed and insured contractors who handle the rebuild from drywall to paint. You get a written, line-itemed scope before anyone picks up a hammer.
Restoration is drywall, trim and flooring work done on a house that just got soaked. The independent pros in our network do that kind of work every week in Arlington.
The rebuild contractor you reach through our line is an independent local outfit with its own license and insurance. Ask to see the insurance certificate before work starts, and any solid contractor will hand it over.
The estimate comes in writing, broken out by square feet of drywall, linear feet of baseboard and hours of labor. Many write it in the line-item style adjusters already use, which cuts the back and forth on the claim.
A rebuild is rarely a 2 a.m. emergency, but waiting weeks for a bid stalls the whole claim. The dispatcher sets a real walkthrough window on the call with a contractor based close to Arlington.
Rebuild crews carry texture hoppers, knockdown knives, trim saws and coping saws, not air movers. That gear and some patience are what make a patched wall look like it was never cut.
Each job follows the scope of loss: a written list of every material that came out during mitigation and has to go back in.
Flood cuts get closed with new board, then tape, three coats of mud and sanding. The hard part is texture: orange peel, knockdown and skip trowel all have to blend into the wall that stayed.
MDF base that drank up water stays swollen, so it gets pulled and replaced with the same profile. Cabinet toe-kicks, and sometimes the sink base itself, get the same treatment after a kitchen leak.
Laminate and LVP tend to get replaced since water sits below the click joints and the core swells. Solid hardwood caught early can often be sanded and refinished; engineered planks rarely come back.
The crew cuts a small chip from a dry wall and has the paint store scan it for a match. Repainting full walls to the corners avoids the shiny halo you get from spot painting.
Contents can be boxed, listed and stored off-site so the crew has open rooms to work in. That inventory also backs up the contents side of your insurance claim.
Before and after photos, the scope, the mitigation drying records and the final invoice go into one file. A complete file usually means fewer re-inspections and fewer arguments over supplements.
The first half of any water loss is mitigation: stop the source, pull the water, remove what will not dry and run dehumidifiers until the meter says done. Restoration is everything after that, and it is much closer to remodeling than to cleanup.
Take a dishwasher supply line that dripped under the cabinets for days before anyone noticed. The dry-out crew pulls the toe-kicks, drills or opens the cabinet bases and dries the subfloor. Restoration means sourcing a toe-kick that matches, swapping a swollen sink base and blending new flooring into the old at the doorway.
Or think about an upstairs toilet that overflowed and rained down through the kitchen ceiling. After the wet ceiling drywall is cut out and the joists dry, someone still has to hang board overhead, match the texture and paint the full ceiling plane.
The crews that are great at fast tear-out are not always the ones you want doing finish work in your living room.
Plenty of companies only do the dry-out. Ask any contractor directly whether the rebuild is included, and make sure the answer is in the written scope.
The process has four steps, and the first is a short phone call.
Tell the dispatcher what was removed during mitigation and whether you have an open claim. We connect you with an independent rebuild contractor who works in Arlington and confirm a walkthrough time.
Your contractor checks every affected room with a meter first, because closing up a wet wall is the most expensive mistake in this trade.
You get a written scope with every line item: drywall, trim, flooring, paint, cabinet work and contents handling. Many contractors submit it to the adjuster and add a supplement if more damage shows up behind a wall.
At the end you walk every room with the contractor and write down anything that does not look right. Nothing gets signed until the punch list is done, and any workmanship warranty should be on paper.
Our dishwasher line leaked under the cabinets for days. When the drying crew left, the sink base was swollen and the toe-kicks were sitting in the garage. The referral line put me in touch with a local contractor who matched the cabinet toe-kicks and talked to our adjuster so I was not stuck in the middle.
Our kids clogged the upstairs toilet, it overflowed, and the kitchen ceiling ended up with a hole the size of a door. The contractor I was connected with hung new board, matched the knockdown and painted the whole ceiling. I honestly cannot find the patch.
I was sure the oak floor in our hallway was a total loss. The contractor I reached through the referral service checked the boards, said they were solid oak and dry, and refinished them rather than replacing them. Honestly the floor looks better now than before the leak.
My rental had three rooms stripped to the studs and a tenant asking every day when it would be done. The contractor gave me a line-item scope the insurance company accepted almost as written, and the paint matched on the first try.
One call connects you with an independent local contractor who handles the rebuild after water damage.
Mitigation is the emergency work that keeps damage from growing: water removal, tear-out, antimicrobial and drying. Restoration is the rebuild that follows: new drywall, matched texture, trim, flooring, cabinets and paint.
Adjusters often see them as two estimates on one claim, sometimes from two different contractors.
That comes down to scope: one room of board and paint goes quickly, but a kitchen with cabinets and flooring takes much longer. The delays usually come from backordered materials and claim approvals rather than the actual work.
Ask your contractor for a written schedule with the order of trades.
Generally you can. Your carrier may recommend a preferred vendor, but most policies let you hire the contractor you pick. Check your own policy and confirm with your adjuster before you sign a contract.
Many contractors in our network work directly with adjusters and write estimates in the format insurers expect.
Often, if they are solid hardwood and were dried quickly. Mild cupping can settle once the moisture content comes back to normal. The contractor checks readings over several days before deciding to sand and refinish.
Engineered flooring and boards that crowned, split or buckled usually need replacing.
They should, if the contractor matches the texture on a test piece and repaints full walls instead of spot painting. The paint is matched from a chip cut out of the original wall, not from an old can label.
Ask to see the texture sample before it goes on the wall, and walk the room in daylight before sign-off.
The contractors we refer live and work in the area, so they know the local housing stock and the local permit office.
Older houses close to downtown Arlington often have plaster and real wood trim, which take more work to match. Newer neighborhoods have MDF trim and LVP, which are easy to buy but swell fast once wet.
Tell us what came out and we will connect you with a local contractor.
Call +1-877-637-9008