Licensed and Insured Drying Contractors
Every contractor we refer is an independent local business that carries its own license and insurance. Many train to the IICRC S500 standard for water damage drying; ask your tech about their certifications.
24/7 Drying Line Open
Structural Drying in New Glarus, WI
Once the puddles are mopped up, a house can look done while the studs, subfloor and drywall core are still soaked inside. Drying a building is a measured process, run by meters and math, not by how a surface feels to your hand.
One call to our referral line puts you in touch with a licensed, insured independent drying contractor serving New Glarus. Your tech sets dehumidifiers and air movers to a plan, logs readings every day and gives you a written estimate up front.
- Drying goals set against unaffected material
- Daily moisture logs and drying charts
- Licensed, insured independent drying contractors
- In-place drying where it saves materials
While the drying runs
- Keep all equipment running around the clock
- Keep windows and doors closed unless told otherwise
- Keep the heat or AC at the setting your tech gives
- Do not move air movers or dehumidifiers
Why people call for drying
Why Choose Our Specialized Structural Drying Network in New Glarus, WI
Proper drying is part science and part routine: read the air, read the materials, adjust, and repeat until the numbers line up. Here is what the independent contractors we refer bring to that work.
Upfront Written Drying Estimates
The estimate lists equipment counts, expected drying days and monitoring visits, so the bill is easy to follow. Daily logs back up each line for the adjuster.
Fast Response From Nearby Techs
Starting early often means drywall, baseboard and floors can be dried in place rather than replaced. Our dispatcher confirms a real arrival window with a nearby tech while you are on the line.
Hygrometers, Pin Meters and LGR Units
Drying techs carry thermo-hygrometers to read temperature, relative humidity and grains per pound, plus pin and pinless meters for wood and drywall. Their trucks carry LGR and desiccant dehumidifiers, cavity injection systems for walls and suction mats for hardwood floors.
Notes from the drying techs
Dry to the Touch Is Not Dry
A familiar story: the leak is repaired and the wall looks normal, yet the meter tells a different tale. Drywall paint dries on the surface first and seals moisture inside the gypsum core and the stud behind it. Close that up or hang a picture on it and you can end up with mold you will not see for weeks.
The drying target comes from what techs call the dry standard: readings taken on unaffected drywall, framing or flooring elsewhere in the house. Only when the wet material matches that baseline is it considered dry, and not a day before.
Hardwood floors show the same problem in a different way. With a slow leak under a dishwasher, the underside of the boards swells and the edges lift, which is called cupping. Sand it flat too early and it crowns once it dries. Drying mats and patient monitoring often let the boards settle back down.
The short version: dry, warm air draws water out of materials, dehumidifiers remove it from the air, and air movers sweep the surface so evaporation keeps going.
- Relative humidity is how full the air is relative to what it can hold at that temperature
- GPP is the actual weight of water vapor in the air, which is the number techs track day to day
- Moisture moves from high vapor pressure in wet materials toward lower pressure in drier air
- Dew point is where the air would condense on a cold surface, which matters on slabs and exterior walls
Where drying equipment goes
Structural Drying Work Done by Local Techs
Techs start by rating the job Class 1 through 4, which sets how much dehumidification and airflow it takes.
Moisture Mapping and the Dry Standard
With meters and thermal imaging, the tech outlines the wet zone and reads unaffected material to set a target. Readings are noted on a floor sketch so the same points are checked each visit.
Rating the Loss by Class
Class 1 is a small area with little absorption; Class 4 means dense materials like hardwood, plaster or concrete that hold water deep. That class decides how much drying equipment the tech sets.
- Class 2: a full room, with water wicking a short way up the walls
- Class 3: saturation from overhead, soaking ceiling, walls and floor
LGR and Desiccant Dehumidifiers
Low grain refrigerant (LGR) units pull moisture down to lower GPP than standard dehumidifiers, which suits most homes. Desiccant units work better in cold spaces and on dense materials like hardwood and concrete.
Wall Cavity Injection Drying
Instead of tearing out drywall, the tech can drill small holes at the base of the wall and push dry air into the cavity. For clean water caught early it often saves the wall, and the holes end up behind the baseboard.
Hardwood Floor Drying Mats
Mats seal against the wood and draw moisture up through the boards and the subfloor below. Wood readings are checked against dry flooring in another room until they line up.
Monitoring and Documentation
Every visit the tech records temperature, relative humidity and GPP inside, outside and at the dehumidifier exhaust, plus material readings. The chart proves to the adjuster that drying is on track and shows when it is complete.
From the first reading to the last
Your Drying Job, From Call to Sign-Off
Call Dispatch and Describe What Got Wet
Share the source, the timing and the materials involved, whether drywall, hardwood, carpet or plaster. We connect you with the nearest independent drying tech and confirm an arrival window.
Tech Arrives and Takes First Readings
Your tech records indoor and outdoor air conditions and then maps moisture across walls, floors and ceilings. Readings on dry material in another room set the target.
Drying Plan and Written Estimate
The tech assigns the evaporation class, decides what can be dried in place and what has to come out, and sizes the equipment. A written, itemized estimate comes before any equipment is switched on.
Monitoring, Resolution and Sign-Off
The tech checks readings every day or so, moves or removes equipment as areas dry, and logs every visit. When every point matches the dry standard, the equipment comes out and you sign off with the full drying log in hand.
From drying callers
What Callers Said About Their Drying Jobs
After an upstairs toilet leak, the wall below looked totally normal by the next day. I called the referral line mostly for peace of mind, and the contractor they connected me with put a meter on it and it was soaked behind the paint. They injected air into the wall cavity instead of tearing it out and showed me the readings dropping every day.
A slow leak under our dishwasher made the kitchen oak floor cup. I figured we would need a new floor. My tech set up drying mats and compared the boards to dry flooring in the dining room each visit. Most of it settled back down, and they were upfront about the few boards that still needed attention.
The machines were loud and I wanted to shut them off at night. The tech explained that turning them off lets the humidity climb back up and basically undoes the day's progress. We left them on and it was done in about four days.
Common drying questions
Structural Drying Questions, Answered
How long does structural drying take?
Many jobs finish in three to five days, while hardwood, plaster or concrete can stretch that out. The evaporation class, the weather and how quickly drying started all change the timeline. Your tech can update the estimate as the daily readings come in.
Why do the drying machines have to run 24 hours a day?
The equipment keeps the air drier than the wet materials, which is what pulls moisture out of them. Once the machines stop, the air humidity climbs back up and the materials stop drying or soak some back in.
Can I turn the drying equipment off at night?
It is best not to. Turning the equipment off overnight usually adds days to the job. If noise is a real problem, ask your tech whether a unit can be repositioned; do not move or switch off machines on your own.
How do they know when the structure is completely dry?
Readings on the affected materials are checked against the same material in a dry room, which is the dry standard. Once every point on the moisture log reaches that range, the job is considered dry. You get the daily log as proof for your records and your adjuster.
How much electricity do drying machines use?
A dehumidifier and several air movers running around the clock will raise the power bill for that period. Many insurers reimburse that added electricity cost on a covered claim, so ask your adjuster and keep your utility bills. The tech can also plan circuits so breakers do not trip.
Where techs respond
Independent Drying Contractors Serving New Glarus
The independent drying contractors we refer work homes, condos and small commercial spaces across New Glarus.
We also hear from people whose space was already dried but still smells musty or shows moisture. A second set of readings from an independent tech can tell you where things stand.
- Drywall and framing
- Cupped wood floors
- Subfloors
- Plaster walls
- Ceilings
Reach the drying line now
Describe the materials and timing, and we will match you with a nearby independent drying tech.
Call +1-877-637-9008Walls or Floors Still Damp? Call Now
A tech with a meter can tell you in minutes whether your walls and floors are really dry. One call connects you with an independent drying contractor nearby.
