Licensed and Insured Drying Contractors
Every contractor we refer is an independent local business that carries its own license and insurance. Many train to the IICRC S500 standard for water damage drying; ask your tech about their certifications.
24/7 Drying Line Open
Structural Drying in Memphis, FL
Once the puddles are mopped up, a house can look done while the studs, subfloor and drywall core are still soaked inside. Drying a building is a measured process, run by meters and math, not by how a surface feels to your hand.
One call to our referral line puts you in touch with a licensed, insured independent drying contractor serving Memphis. Your tech sets dehumidifiers and air movers to a plan, logs readings every day and gives you a written estimate up front.
- Targets set from dry material in the same house
- Daily moisture logs and drying charts
- Independent local techs with license and insurance
- Drying in place before tearing anything out
While the drying runs
- Keep all equipment running around the clock
- Hold windows shut unless the tech says to open them
- Set the thermostat where the tech recommends
- Leave the fans and dehus exactly where they sit
Why people call for drying
Why Choose Our Specialized Structural Drying Network in Memphis, FL
Proper drying is part science and part routine: read the air, read the materials, adjust, and repeat until the numbers line up. Here is what the independent contractors we refer bring to that work.
Written Estimates Tied to the Drying Plan
The estimate lists equipment counts, expected drying days and monitoring visits, so the bill is easy to follow. Daily logs back up each line for the adjuster.
Fast Response From Nearby Techs
The sooner drying starts, the more drywall, trim and flooring can stay in place instead of being cut out. Our dispatcher confirms a real arrival window with a nearby tech while you are on the line.
Hygrometers, Pin Meters and LGR Units
Expect a thermo-hygrometer for temperature, humidity and GPP, pin and non-invasive meters for framing and drywall, and a thermal camera to track cool, wet areas. Equipment ranges from LGR and desiccant dehumidifiers to wall cavity injection kits and hardwood floor drying mats.
Notes from the drying techs
Dry to the Touch Is Not Dry
Here is a call the dispatch desk gets every week: a leak was fixed, the wall looks fine, but a tech puts a meter on it and it reads high. Drywall paint dries on the surface first and seals moisture inside the gypsum core and the stud behind it. Close that up or hang a picture on it and you can end up with mold you will not see for weeks.
The drying target comes from what techs call the dry standard: readings taken on unaffected drywall, framing or flooring elsewhere in the house. When the wet wall reads within range of that dry standard, it is dry; until then, the equipment keeps running.
Hardwood floors show the same problem in a different way. With a slow leak under a dishwasher, the underside of the boards swells and the edges lift, which is called cupping. Sand it flat too early and it crowns once it dries. Drying mats and patient monitoring often let the boards settle back down.
The short version: dry, warm air draws water out of materials, dehumidifiers remove it from the air, and air movers sweep the surface so evaporation keeps going.
- Relative humidity is how full the air is relative to what it can hold at that temperature
- Grains per pound (GPP) measures how much water is actually in the air, regardless of temperature
- Moisture moves from high vapor pressure in wet materials toward lower pressure in drier air
- Dew point is where the air would condense on a cold surface, which matters on slabs and exterior walls
Where drying equipment goes
Structural Drying Work Done by Local Techs
Every drying job starts by sorting the loss into an evaporation class, which tells the tech how much equipment the space needs.
Mapping Wet Areas Against Dry Readings
The tech maps the wet area with meters and a thermal camera, then takes readings on unaffected material to set the drying goal. Readings are noted on a floor sketch so the same points are checked each visit.
Rating the Loss by Class
A Class 1 loss touches a small area, while Class 4 involves deep-holding materials such as hardwood, plaster and concrete. That class decides how much drying equipment the tech sets.
- Class 2: whole room, wicking under a foot or two up the walls
- Class 3: saturation from overhead, soaking ceiling, walls and floor
Choosing the Right Dehumidifier
LGR dehumidifiers drive the air drier than a standard unit, which is what most residential jobs need. Desiccant units work better in cold spaces and on dense materials like hardwood and concrete.
Wall Cavity Injection Drying
Rather than cutting the wall open, the tech can drill small holes behind the baseboard and inject dry air into the stud bays. It works well for clean water caught early, and the holes hide under the trim.
Saving Cupped Hardwood
Mats seal against the wood and draw moisture up through the boards and the subfloor below. The tech tracks readings on the boards against dry wood elsewhere until they match.
Monitoring and Documentation
Each monitoring visit logs temperature, humidity and GPP in the affected area, outdoors and at the dehumidifier outlet, along with material readings. That chart shows the adjuster the job is drying as planned, and when it is done.
How a drying job runs
How Structural Drying Works, Step by Step
Call Dispatch and Describe What Got Wet
Tell the dispatcher what kind of water it was, how long ago it happened and which materials got wet. We route the call to the closest independent drying tech and give you an arrival window.
Tech Arrives and Takes First Readings
Your tech records indoor and outdoor air conditions and then maps moisture across walls, floors and ceilings. Readings on dry material in another room set the target.
Drying Plan and Written Estimate
The tech assigns the evaporation class, decides what can be dried in place and what has to come out, and sizes the equipment. A written, itemized estimate comes before any equipment is switched on.
Daily Checks Until Dry, Then Sign-Off
Monitoring visits happen about daily, with equipment adjusted or pulled as each area reaches its goal. Once all readings match the dry standard, the gear is picked up and you sign off with the complete log for your claim.
From drying callers
What Callers Said About Their Drying Jobs
Our upstairs toilet leaked and the hallway wall looked completely fine a day later. I called the referral line mostly for peace of mind, and the contractor they connected me with put a meter on it and it was soaked behind the paint. They injected air into the wall cavity instead of tearing it out and showed me the readings dropping every day.
The oak in our kitchen started cupping from a slow leak under the dishwasher. I figured we would need a new floor. My tech set up drying mats and compared the boards to dry flooring in the dining room each visit. Most of it settled back down, and they were upfront about the few boards that still needed attention.
Honestly, I was tempted to switch the fans off overnight because of the noise. The tech explained that turning them off lets the humidity climb back up and basically undoes the day's progress. We kept them running and the job wrapped up in about four days.
Common drying questions
Structural Drying Questions, Answered
How long does structural drying take?
Most clean-water jobs dry in about three to five days, but dense materials like hardwood, plaster and concrete can take longer. The evaporation class, the weather and how quickly drying started all change the timeline. Your tech can update the estimate as the daily readings come in.
Why do the drying machines have to run 24 hours a day?
The equipment keeps the air drier than the wet materials, which is what pulls moisture out of them. Stopping the machines lets humidity rise again, and the materials stop giving up water or even reabsorb it.
Can I turn the drying equipment off at night?
It is best not to. Turning the equipment off overnight usually adds days to the job. If the noise is a real issue, ask your tech about adjusting placement rather than moving or shutting off units yourself.
How do they know when the structure is completely dry?
The tech compares readings on the wet materials to readings on the same material in an unaffected part of the house, called the dry standard. When every logged point matches that standard, the drying goal is met. You get the daily log as proof for your records and your adjuster.
How much electricity do drying machines use?
A dehumidifier and several air movers running around the clock will raise the power bill for that period. Plenty of insurance carriers reimburse the extra electricity on covered claims, so ask your adjuster and save the bills. Your tech will spread the load across circuits so nothing trips.
Local drying coverage
Structural Drying Techs Around Memphis
Our network of independent drying techs covers houses, condos and small businesses all over Memphis.
We also hear from people whose space was already dried but still smells musty or shows moisture. A fresh set of readings from an independent tech can settle the question.
- Drywall and framing
- Cupped wood floors
- Subfloors
- Older plaster
- Ceilings
Reach the drying line now
Describe the materials and timing, and we will match you with a nearby independent drying tech.
Call +1-877-637-9008Still Reading Wet? Get It Measured
A tech with a meter can tell you in minutes whether your walls and floors are really dry. One call connects you with an independent drying contractor nearby.
