Licensed and Insured Drying Contractors
Every contractor we refer is an independent local business that carries its own license and insurance. Many train to the IICRC S500 standard for water damage drying; ask your tech about their certifications.
24/7 Drying Line Open
Structural Drying in Clovis, CA
The water is gone, the carpet feels fine and the wall looks normal, but the framing behind it can still be holding a surprising amount of moisture. Drying a building is a measured process, run by meters and math, not by how a surface feels to your hand.
Call Doral Water Damage and our dispatcher connects you with a licensed, insured independent drying contractor who works near Clovis. Your tech sets dehumidifiers and air movers to a plan, logs readings every day and gives you a written estimate up front.
- Drying goals set against unaffected material
- Readings recorded on every monitoring visit
- Independent local techs with license and insurance
- Drying in place before tearing anything out
While the drying runs
- Leave every machine on, day and night
- Keep windows and doors closed unless told otherwise
- Keep the heat or AC at the setting your tech gives
- Leave the fans and dehus exactly where they sit
Why callers use this line
Why Choose Our Specialized Structural Drying Network in Clovis, CA
Proper drying is part science and part routine: read the air, read the materials, adjust, and repeat until the numbers line up. Here is what the independent contractors we refer bring to that work.
Upfront Written Drying Estimates
The estimate lists equipment counts, expected drying days and monitoring visits, so the bill is easy to follow. Daily logs back up each line for the adjuster.
Rapid Local Dispatch
The sooner drying starts, the more drywall, trim and flooring can stay in place instead of being cut out. Our dispatcher confirms a real arrival window with a nearby tech while you are on the line.
Hygrometers, Pin Meters and LGR Units
Expect a thermo-hygrometer for temperature, humidity and GPP, pin and non-invasive meters for framing and drywall, and a thermal camera to track cool, wet areas. Equipment ranges from LGR and desiccant dehumidifiers to wall cavity injection kits and hardwood floor drying mats.
Notes from the drying techs
Why Dry to the Touch Does Not Mean Dry
Here is a call the dispatch desk gets every week: a leak was fixed, the wall looks fine, but a tech puts a meter on it and it reads high. Painted drywall dries at the face while the gypsum core and the stud behind it stay wet. Close that up or hang a picture on it and you can end up with mold you will not see for weeks.
The drying target comes from what techs call the dry standard: readings taken on unaffected drywall, framing or flooring elsewhere in the house. When the wet wall reads within range of that dry standard, it is dry; until then, the equipment keeps running.
Hardwood floors show the same problem in a different way. With a slow leak under a dishwasher, the underside of the boards swells and the edges lift, which is called cupping. Sanding it flat too soon leaves the floor crowned once it finishes drying. Drying mats and steady monitoring can often bring the boards back flat.
The short version: dry, warm air draws water out of materials, dehumidifiers remove it from the air, and air movers sweep the surface so evaporation keeps going.
- Relative humidity is how full the air is relative to what it can hold at that temperature
- GPP is the actual weight of water vapor in the air, which is the number techs track day to day
- Vapor pressure moves moisture from wetter materials toward drier air
- Dew point tells the tech where condensation could form on cold slabs and outside walls
What the techs dry
What a Drying Job Actually Covers
Every drying job starts by sorting the loss into an evaporation class, which tells the tech how much equipment the space needs.
Moisture Mapping and the Dry Standard
The tech maps the wet area with meters and a thermal camera, then takes readings on unaffected material to set the drying goal. Those readings get marked on a sketch so every visit checks the same spots.
Rating the Loss by Class
Class 1 is a small area with little absorption; Class 4 means dense materials like hardwood, plaster or concrete that hold water deep. The class drives how many dehumidifiers and air movers go in.
- Class 2: whole room, wicking under a foot or two up the walls
- Class 3: saturation from overhead, soaking ceiling, walls and floor
LGR and Desiccant Dehumidifiers
Low grain refrigerant (LGR) units pull moisture down to lower GPP than standard dehumidifiers, which suits most homes. Desiccant units work better in cold spaces and on dense materials like hardwood and concrete.
Drying Inside Closed Walls
Rather than cutting the wall open, the tech can drill small holes behind the baseboard and inject dry air into the stud bays. For clean water caught early it often saves the wall, and the holes end up behind the baseboard.
Hardwood Floor Drying Mats
Panels sealed to the floor pull air through the boards and the subfloor under vacuum. The tech tracks readings on the boards against dry wood elsewhere until they match.
Monitoring and Documentation
Each monitoring visit logs temperature, humidity and GPP in the affected area, outdoors and at the dehumidifier outlet, along with material readings. That chart shows the adjuster the job is drying as planned, and when it is done.
How a drying job runs
How Structural Drying Works, Step by Step
Call Dispatch and Describe What Got Wet
Share the source, the timing and the materials involved, whether drywall, hardwood, carpet or plaster. We route the call to the closest independent drying tech and give you an arrival window.
Rapid Mobile Arrival With Meters
The tech reads the air inside and outside, then maps moisture through the walls, floors and ceilings. A few readings on unaffected material elsewhere set the drying goal.
Expert Assessment and Written Quote
The tech assigns the evaporation class, decides what can be dried in place and what has to come out, and sizes the equipment. You get a written, line-itemed estimate before the machines start.
Monitoring, Resolution and Sign-Off
Monitoring visits happen about daily, with equipment adjusted or pulled as each area reaches its goal. Once all readings match the dry standard, the gear is picked up and you sign off with the complete log for your claim.
From drying callers
Drying Stories From Our Callers
Our upstairs toilet leaked and the hallway wall looked completely fine a day later. I called the referral number to be safe, and the local contractor they put me through to found the wall was wet inside. They injected air into the wall cavity instead of tearing it out and showed me the readings dropping every day.
A slow leak under our dishwasher made the kitchen oak floor cup. I was ready to replace the whole floor. My tech set up drying mats and compared the boards to dry flooring in the dining room each visit. It flattened most of the way, and they told us honestly which boards would still need work.
Honestly, I was tempted to switch the fans off overnight because of the noise. The tech explained that turning them off lets the humidity climb back up and basically undoes the day's progress. We left them on and it was done in about four days.
Drying questions
Straight Answers About Structural Drying
How long does structural drying take?
Many jobs finish in three to five days, while hardwood, plaster or concrete can stretch that out. The evaporation class, the weather and how quickly drying started all change the timeline. Your tech can update the estimate as the daily readings come in.
Why do the drying machines have to run 24 hours a day?
Drying works by keeping the air drier than the wet materials so moisture keeps moving out of them. Once the machines stop, the air humidity climbs back up and the materials stop drying or soak some back in.
Can I turn the drying equipment off at night?
It is best not to. Turning the equipment off overnight usually adds days to the job. If noise is a real problem, ask your tech whether a unit can be repositioned; do not move or switch off machines on your own.
How do they know when the structure is completely dry?
The tech compares readings on the wet materials to readings on the same material in an unaffected part of the house, called the dry standard. Once every point on the moisture log reaches that range, the job is considered dry. You get the daily log as proof for your records and your adjuster.
How much electricity do drying machines use?
A dehumidifier and several air movers running around the clock will raise the power bill for that period. Plenty of insurance carriers reimburse the extra electricity on covered claims, so ask your adjuster and save the bills. The tech can also plan circuits so breakers do not trip.
Where techs respond
Independent Drying Contractors Serving Clovis
Our network of independent drying techs covers houses, condos and small businesses all over Clovis.
Some callers reach us after another company dried the space and something still smells musty or reads wet. A second set of readings from an independent tech can tell you where things stand.
- Drywall and framing
- Hardwood floors
- Subfloors
- Older plaster
- Ceilings
Reach the drying line now
Tell us what got wet and when, and we will connect you with an independent drying tech near Clovis.
Call +1-877-637-9008Still Reading Wet? Get It Measured
In a few minutes with a meter, a tech can tell you whether the structure is actually dry. One call connects you with an independent drying contractor nearby.
